Reducing Product Testing and Certification Costs

Do you regularly need testing and certification services for your products? How to reduce testing and certification costs of your products?

There are some tips to reduce these costs.

Click below link and read more about it:

Full Anechoic Chamber

EMC tests are performed in special test chambers. This EMC chamber is for performing radiated emission and immunity tests. We can measure up to 18GHz.

Full Anechoic Chamber (FAC)

When you need EMC testing service or radiated immunity testing service click here and send your request online.

Accredited RED, EMC testing

Radio Equipments need testing and certification before putting them in European countries which CE marking directives are mandatory.

Do you want to certify your radio equipments according to Radio Equipment Directive (2014/53/EU) and sell your products to whole Europe?

We are providing EN 17025 accredited testing and certification services according to below ETSI standards.

ETSI EN 300 328
ETSI EN 301 489-1
ETSI EN 301 489-3
ETSI EN 301 489-17
ETSI EN 301 489-52
ETSI EN 301 511
ETSI EN 301 908-1
ETSI EN 301 893

Contact Ege Test Center when you need testing and certification services for your radio equipments:

Radio Equipment Directive 2014/53/EU

Radio Equipment Directive (RED, 2014/53/EU) is one of the directives published by European Union regulating the compliance of radio equipments. For CE marking of radio equipments, RED is one of the essential directives. RED ensures a single market for radio equipment by setting essential requirements for:

  • safety and health,
  • electromagnetic compatibility,
  • the efficient use of the radio spectrum

In addition to these three items, technical features for the protection of privacy, personal data and against fraud, interoperability, access to emergency services, and compliance regarding the combination of radio equipment and software are also regulated with RED (Radio Equipment Directive, 2014/53/EU).

Each country applying CE marking regulations have local authorities for market surveillance. They are regulating the market and giving penalties for unsafe products in the market.

Radio Equipment Directive (2014/53/EU)

Radio Equipment Directive (2014/53/EU) of European Union is getting popular parallel to technological developments.

What is Radio Equipment Directive (RED)?
Which tests are required according to RED?
How to perform Safety, EMC and Radio tests?
Ask Ege Test Center, one of our engineers will reply your questions:
Ege Test Center

Subscribe to Testups Turkey e-mail list to receive our announcements!

Why Pre-Compliance EMC Testing?

Electromagnetic Compatibility (EMC) testing is one of the essential requirements prior to marketing electrical products. Most of the electrical equipments need EMC testing due to some technical and legal reasons. EMC test standards are varying according to the region or country that the product will be marketed to. Product designers and manufacturers have to be aware of these standards and shall market their products according these regional or international standards. Prior to full compliance EMC testing, pre-compliance EMC testing plays an essential role. By performing some of EMC tests in their own facilities, product designers and manufacturers will ensure that their products fulfill EMC testing standards partially. This will give them a great advantage prior to full compliance EMC testing or certification of the products by third party testing laboratories.

In order to set up a pre-compliance EMC testing laboratory, there are many solutions on the market. These solutions depend on the features of the Equipment Under Test (EUT). By listing the EMC test standards and specific tests according the product features, EMC testing chambers or equipments can be selected. These pre-compliance EMC test equipments will not cost as much as accredited EMC testing laboratories since some deviations can be ignored due to the tests are pre-compliance.

Picture link:


Remark: This post is firstly published on Linkedin by Yusuf Ulas KABUKCU:

EMC Directive in non-EU States, countries & territories

European Union published a guide regarding Electromagnetic Compatibility (EMC) directive: Guide for the EMCD (Directive 2014/30/EU)

As this EMC Directive Guide mentions, the geographical application is described in Chapter 2.8 “geographical application” of the Blue Guide. The EMCD also applies in the EEA-EFTA States (Liechtenstein, Iceland, and Norway) and Turkey. Therefore, when the terms “European Union”, “Union”, “territory” or ‘Member States’ are used in this Guide, they apply to the EEA-EFTA States (Liechtenstein, Iceland, and Norway) and Turkey.

How to get EMC testing services?

You have to contact an EMC testing laboratory expert who is experienced in EMC testing. Ege Test Center experts provide you required information about EMC testing and certification of your product. Do you want to pass EMC tests and affix CE marking on your products? Contact us by visiting our contact page.

Ege Test Center helps designers, manufacturers, engineers, importers, exporters, researchers, universites and all other parties need EMC testing according to EMC Directive. You can ask any question regarding EMC Directive or send your request by using our Online Application form:

Conducted Emission Testing

Conducted Emission testing, one of the EMC tests, is applied to many electrical products. In this test, it is checked whether the unwanted frequencies emitted from the cables of the products are below the limits.

Conducted Emission Testing

Conducted Emission testing is one of the EMC tests. With Conducted Emission test, electromagnetic unwanted signals emitted from the cables of the product to be tested or I/O ports are measured. Depending on the test standard to be applied, the unwanted signals in the 9kHz-30MHz range are usually measured to determine whether the test is below the specified limit in the test standard. The measured value in the Conducted Emission test is uV (micro volt) because of the conducted voltage measurement. In order to make the limits in frequency spectrum and test standards more clear, this unit is used with logarithmic expression (dBuV) and compared with the limits in the standard.

The devices and auxiliary items used in the Conducted Emission test are as follows:

EMI Receiver,

RF Cable,

Line Impedance Stabilization Network (LISN),

Isolation Transformer,

Appropriate Test Table,

Grounding Cables,

Computer and Test Software (for automatic Conducted Emission testing)

The scan is carried out using the EMI Receiver from the Conducted Emission test to measure peak and average values ​​of the signals. As a result of scanning in the EMI Receiver, the Peak and Average measurement results are compared to the limits specified in the test standard. For peak values, it is usually necessary to perform manual additional measurements after scanning, since Quasi-Peak (QP) limits are given. The EMC test expert who conducts the Conducted Emission test, completes the test after completing the QP measurements and evaluating whether the product has passed the test. Tests are carried out according to test standards starting with IEC, EN or other ones…

Conducted Emission test is one of the EMC tests which is closely related to many sectors from the lighting industry to the defense industry. Since many products have cables or I/O ports, the electromagnetic effects that may occur here may affect other products or systems. One of the EMC tests, Conducted Emission test, is used to prevent this interaction. We can also give examples of everyday life regarding the Conducted Emission test: the impact of a television operating in the same environment while the vacuum cleaner is operating. The vacuum cleaner and television use a common supply (mains) network as they are fed from the same network, so if the vacuum cleaner emits electromagnetic signals unwanted signals, we call it operation emission. If this spread is above the limits, the television may be adversely affected by these signals, resulting in loss of performance in the sound or image.

Electromagnetic Wave

During the Conducted Emission test, the products failing from the test are subjected to various modifications and R&D works. The most well-known modifications are the use of EMI filters, review of grounding and the use of EMI/EMC-compliant components. For example, a filter (R-L-C) design may be required in accordance with an electrical product with an emitting signal at 10MHz above the limit. After applying some changes, the product is subjected to same Conducted Emission test and the effect of the change is observed.

You can submit your questions and requests regarding Conducted Emission Test and other EMC tests to Ege Test Center online: Online Application Form

Our services and products related to Conducted Emission testing are as follows:

Testing and laboratory services

Supply of test equipments

Theoretical and Applied Trainings/Courses

Consultancy Services

R&D works

For Europe, Conducted Emission tests of radio equipments are performed according to ETSI standards. One of the milestones of EMC tests is the Conducted Emission testing. Ege Test Center provides pre-compliance, engineering and accredited Conducted Emission testing and certification services according to relevant standards.

Click here to get quote from Ege Test Center

Our References (International)

EEG Shielded Rooms

EEG Shielded Rooms

The EEG-SR of Testups Turkey is a protected room designed specifically for use in medical environments to provide optimum performance at VLF / ELF frequencies. This helps protect the highly sensitive test equipment inside the room from interference.


  • EEG (Electroencephalogram)
  • EMG (Electromyogram)
  • ECG (Electrocardiogram)


  • Magnified interior space.
  • The test facility can be configured to your exact requirements.
  • Industry-protected door with copper beryllium edge seal.
  • Adjustable fiber optic lighting.
  • Sound insulation

For detailed information on the Testups Turkey’s EEG Protected Room, please fill out the form at